點膠機的針頭與膠水使用時應該注意啥？
本身就是控制分配膠機吐痰和吐出的設備,因此使用點膠機勢必影響到電動膠的質量問題解決:膠方面的膠水,膠水不能有氣泡,小氣泡會導致大量的焊盤沒有膠水,空現象,可能導致不合格的產品。
It is the equipment to control the spitting and spitting of the dispensing glue machine. Therefore, the use of the dispensing machine will inevitably affect the quality problem solving of the electric glue: the glue in the aspect of glue, the glue can not have bubbles, small bubbles will lead to a large number of pads without glue, empty phenomenon, which may lead to unqualified products.
所以每更換一半的膠管必須空接，關于膠的固化，一般廠家都給出了溫度曲線。在實踐中應盡量選擇溫度較高的固化，使固化后的膠水達到強度要求。
Therefore, every half of the rubber tube to be replaced must be air jointed. For the curing of the rubber, the general manufacturer has given the temperature curve. In practice, we should try our best to choose a high temperature curing to make the cured glue meet the strength requirements.
膠粘劑的粘度直接影響著膠液的質量。粘度高，上膠點小，拉絲均勻;粘度小時，膠點會變大，然后可能滲到膠墊上。在配膠過程中，對不同粘度的膠應選擇合理的背壓和配膠速度。
The viscosity of adhesive directly affects the quality of glue solution. The viscosity is high, the glue point is small, and the drawing is even; when the viscosity is small, the glue point will become larger, and then it may seep onto the rubber pad. In the process of dispensing, a reasonable back pressure and dispensing speed should be selected for different viscosities.
除去膠水和外部環境的影響，關于點膠機本身，一般企業點膠機都是選用螺桿泵點膠針。
In addition to the influence of glue and external environment, as for dispensing machine itself, screw pump dispensing needle is generally used in enterprise dispensing machine.
因此，需求采用恒壓，保證螺桿泵能滿足膠水供應。如果壓力過小，就會出現間歇點膠、滲漏的現象，進而造成缺陷。
Therefore, constant pressure is required to ensure that the screw pump can meet the glue supply. If the pressure is too small, there will be intermittent dispensing and leakage, which will cause defects.
所以應根據膠液質量的不同，分膠機工作環境的溫度來選擇壓力。較高的環境溫度會使膠水粘度變小，流動性更好，這時需要減少背壓以保證膠水的供應，反之亦然。
Therefore, the pressure should be selected according to the temperature of the working environment of the dispenser according to the quality of the glue. Higher ambient temperature will make the glue viscosity smaller and fluidity better. At this time, it is necessary to reduce the back pressure to ensure the supply of glue, and vice versa.
在實踐中，我們認為針的內徑尺寸應該是點膠點直徑的1/2，這是更理想的點膠方式。因此，在點膠過程中，應根據PCB上焊盤的大小選擇點膠針，以保證點膠點的質量，提高生產功率。
In practice, we think that the inner diameter of the needle should be 1 / 2 of the dispensing point diameter, which is the most ideal dispensing way. Therefore, in the dispensing process, the dispensing needle should be selected according to the size of the pad on the PCB to ensure the quality of the dispensing point and improve the production power.
不同的配藥器選用不同的配針，有些配針有一定程度的停藥。在每一次操作的開始，都要對針與PCB之間的間距進行校準，即z軸高度校準，這一點往往被忽略。
Different dispensing devices choose different dispensing needles, some of which have a certain degree of drug withdrawal. At the beginning of each operation, the clearance between the pin and PCB should be calibrated, that is, z-axis height calibration, which is often ignored.
根據操作經驗，膠點直徑應為焊盤距離的一半，補片后的膠點直徑應為膠點直徑的1.5倍。
According to operation experience, the diameter of glue point shall be half of the distance between pads, and the diameter of glue point after patch shall be 1.5 times of the diameter of glue point.
這確保有足夠的膠水來保持元件在一起，并防止過多的膠浸漬墊。上膠量由螺桿泵的旋轉時間決定。實際使用時，應根據室溫和膠水的粘度來選擇泵的旋轉時間。
This ensures that there is enough glue to keep the components together and to prevent excessive glue impregnation. The amount of glue is determined by the rotation time of screw pump. In actual use, the rotation time of the pump should be selected according to the room temperature and the viscosity of the glue.
This article is published by http://www.e846lbsv.cn
上一篇：中空玻璃打膠機有哪些實用性效果？
下一篇：中空玻璃膠機的調試方法？
